AIR PARADISE SOLUTIONS AIR DUCT AND CARPET | 1-866-946-9247 | AIR DUCT CLEANING | CARPET CLEANING | UPHOLTERY CLEANING

Air-Care Electrostatic Air Filters clean the air by using static electricity, a safe, naturally occurring phenomenon. An electrostatic charge is generated by air flowing through a maze of static prone fibers. Airborne particles are attracted and held by the static charge until released by washing. All Air-Care Electrostatic Filters contain an EPA registered anti-microbial material to inhibit the mold and bacteria growth on the filter surface.
	The ELECTRA SILVER 8200 is designed to meet the special needs of some furnaces and air conditioners that require a very low resistance due to a limited return configuration. The 0.08 inch W.G. initial resistance of the Electra Silver 8200 will assure sufficient air flow to minimize concerns about freezing coils or overheating heat exchangers. The woven polypropylene layer with integral anti-microbial material provides 8 times more filtration than a disposable filter. The non woven polyester pre-filter will maintain high arrestance even when soiled.
	The ELECTRA SILVER 9400 is designed to provide the highest arrestance available for the majority of furnaces and air Conditioners. The 0.12 inch W.G. initial resistance of the Electra Silver 9400 will perform best in systems configured with 1 square foot, or more, of filter area for each ton of air conditioning. Two layers of woven monofilament polypropylene with integral anti-microbial material provide 10 times more filtration than a disposable fiberglass filter. The deep loading center layer of non-woven polyester allows the Electra Silver 9400 to prolong the time between washings.
	The ELECTRA GOLD provides over 94% Arrestance in a premium quality Extruded Aluminum, Gold Anodized frame with a durable and attractive finish. At the heart of this filter are three layers of high arrestance material sandwiched between 2 layers of expanded steel. A special Impregnated black Polypropylene has an EPA registered anti-microbial material to inhibit mold and bacteria growth while the center non-woven layer retains debris in a maze of fibers designed to maximize air flow even when soiled. Rated by independent testing laboratory at over 94% peak arrestance, this filter has 10 times the arrestance of a disposable fiberglass filter.

Specifications 8200:

Peak Arrestance: 82%

Initial Resistance: 0.06 Inches W.G.

Dust Holding Capacity: 119 grams

Lifetime Warranty

Specifications 9400:

Peak Arrestance: 94%

Initial Resistance: 0.12 Inches W.G.

Dust Holding Capacity: 165 grams

Lifetime Warranty

Specifications GOLD:

Peak Arrestance: 94%

Initial Resistance: 0.12 Inches W.G.

Dust Holding Capacity: 165 grams

Lifetime Warranty

MODEL: BEUV

Single Lamp UV for air conditioning coil mount systems 1-3 tons.

Mounts on supply side of AC coil 90% efficent.

115 volt power cord (plugin model)

Specifications: One(1) UVC Lamp 13 watts.

Output: 253.7 nm of UV

MODEL: BEUV2

Dual Lamp UV for air conditioning coil mount systems 3.5-5 tons.

Mounts on supply side of AC coil 99% efficent.

115 volt power cord (plugin model)

Specifications: Two(2) UVC Lamps

13 watts each.

Output: 253.7 nm of UV

MODEL: RB13

Replacement UV Bulb.

13 watts 253.7 nm Germicidal Lamp

For: Models BEUV & BEUV2

Model: RB13

MODEL: BE208

Single Lamp UV for air conditioning coil mount systems 1-7 tons.

Mounts on supply side of AC coil 99% efficent.

277 volt w/ 6FT. OF BX (Hardwire model)

Specifications: One(1) UVC Lamp 18 watts.

Output: 253.7 nm of UV

MODEL: RB18

Replacement UV Bulb.

18 watts 253.7 nm Germicidal Lamp

For: Models BE208

Model: RB18

MODEL: BE2020

Removes Lung Damaging Dust
Safe and effective in helping to eliminate airborne allergens, bacteria, viruses, mold, fungi, and more.
22 Gauge Steel
Low Pressure Drop
Electrostatic Media
MERV 8 Rated
Affordable to the homeowner
Pleated for greater media capacity
Specifications: - One - UL Class 2 Filter

MOLD TESTER


	If you want to prevent mold from growing, here are a few tips. It's most likely to grow in basements and bathrooms -- remember the two Bs. So try to get ventilation in those areas especially. Also try and make sure your entire house has adequate ventilation elsewhere. This is an important point. And try to keep the humidity level in your home below 50 percent. http://transcripts.cnn.com/TRANSCRIPTS/0310/04/smn.06.html

Step 1: Prepare the test solution

Add 15 drops of test solution to the cup.

Step 2: Collect the sample
	Open the package containing the swabs and remove one swab, holding it by the wooden end. Locate an area with obvious mold growth. (Molds of concern typically appear as circular black, green, yellow, brown or white "mats" with black, green or brown spores covering the mat). Use the swab to collect the mold. Collect at least a thumbtack size amount of mold for the test. Don't cover the entire swab (that's too much), and make sure you've got more than a pin-head amount (that's too little).

Step 3: Start the test
	Carefully twirl the swab head containing the mold sample in the solution. The solution should become cloudy or grayish-black.

Step 4: Place the Test Strip in the Cup
	Mold Test Kit contains two tests, use only one test strip per sample. Place the test strip in the sample cup with the arrows pointing down. The end with the arrows should be in the liquid. Wait 5 minutes. Remove the strip from the cup and read (interpret) the test.

Positive = 2 Lines on the strip
Negative = 1 Line
Pink test line and pink control line is a positive result for Stachybotrys chartarum. Grey, brown or black test line and a pink control line is a positive result for Aspergillus niger.

Negative = 1 Line

No line in the test line area and a pink control line is a negative result. This means that there was no detectable Stachybotrys chartarum or Aspergillus niger molds in the sample taken. You may have them in lower concentrations or in other locations. You also may have other molds present.